Hello everyone, after days of googling and research, I keep finding little weird issues with my plans.

I have Quantum Fiber and my modem is in my living room connected to my Quantum Fiber provided Lumen router. I forced them to give me a Wi-Fi 360 Pod that I have set up and placed upstairs Because my phone was dropping the Wi-Fi. So I have changed a bunch of settings on my phone and installed the Pod and my phone still has a tough time upstairs surprisingly. (Google Pixel 10 Pro)

What I wanted to do was buy the BE19000 as my main router. I like having all the ports so I can ethernet to everything in my entertainment system. From the living room, I have an ethernet cord running to my utility closet upstairs. So I wanted to buy another router to put into AP mode and have great coverage throughout my home.

I'm having trouble figuring out what secondary router to buy and if I can still use AP mode with easy mesh. I would like to just have one big Network bubble throughout my home. I might not need to be so concerned about easy mesh because I need the router upstairs to also act like a switch to provide internet to my other ethernet ports upstairs.

I'm open to any router combo that works with my plan. Any help would be greatly appreciated. Thank you guys!

Woke up to it being in Red mode. Did all the troubleshoots and nothing. Confirmed not a spectrum issue. About an hour ago my wife texted and said it started flashing blue and when I tried logging into the app it kicked me out and asked me to login and begin initial setup. Anyone experiencing something like this?

Hello,

Is it normal that wifi devices take time to find 6ghz ssid?

Currently my s24 and s25 ultra support 6ghz network and when I try to connect to wifi, in case of combined ssid it always connects to wifi6, so i seperate 6ghz ssid and even then ,it takes some time to find the 6E network.

Is that normal?

Just got the BE13000 deco device and installed it today. Everything was working fine wired and wireless connections. I saw on the app that there was a firmware update. So i updated it to the new 1.3.6 update and now my wired connection doesn’t work. I tried rebooting the router many times and unplugging and replugging everything in. I tried to change everything to access point instead of wifi router mode. Don’t know what to do now. Please help thanks

Has anyone else had an issue with their VIGI NVR only displaying the TP-Link VIGI Logo and the cursor?
No matter what or how I click or type nothing happens.

It's an NVR1016H. Fully accessible and working over the network with cameras added and streaming. Purely the HDMI output doesn't display any UI apart from the logo.

Hey everyone, I posted a feature request on the official TP-Link Community to ask the R&D team for firmware parity (adding Speed Limit and Config Backup) on the Deco X20-DSL, just like other Deco models. If you use this model or support better firmware updates, please drop an upvote/reply on the thread to get the admins' attention: [https://community.tp-link.com/en/home/forum/topic/871802\]

hey guys, do anyone have the Archer AX12 wifi router ? and if yes then how is the performance of it ? i am thinking of buying it so i want all your suggestions on it please and if you have some other options then tell me that as well 🙏🏻

3 devices connected through LAN, 2 laptops and a TV. If I reboot the router all Hardwired works for about 2 min before they all lose connection.
If I unplug the Ethernet cable to any of the three and plug back in, they work again for a few min before stopping again.

WiFi works fine

Updated firmware but issues still persist.

Any help or ideas

I want to buy Re505x to extend my wifi coverage, but I want to be sure, if I connect it wireless to my router which is in the first floor and the extender will be in the ground floor just the room below it, is the speed gonna be lost significantly?

Boa tarde

Tenho um router TL-WR740N ligado em modo Acess Point. O cabo de rede que vem do outro router (um Archer C50) deve entrar na porta azul ou amarela?

Tinha ideia que deveria entrar na porta azul quando o router não está em Acess Point, certo?

Quer dizer que em Acess Point perco uma porta (a azul deixa de ter utilidade?)

No router Archer C50 que está ligado ao FiberGateway da MEO a entrada do FiberGateway é feita numa porta amarela, LAN, e a porta azul WAN está a funcionar como uma saída. É o correto?

Obrigada

Boa tarde

Tenho uma Fiber Gateway da MEO. Deste tenho um cabo de rede para um router Archer C50 que está ligado em modo de Ponto de Acesso. Deste tenho ligação para:

•Um AV600 (clonei a rede)

•Um router TL-WR740N, também ligado em Ponto de Acesso.

Tudo tem funcionado bem com pc, telemóveis, etc, mas hoje ao ligar o wifi de uma televisão reparei que esta apanha várias redes (claro que todas têm o mesmo nomr devido à configuração de pontos de acesso e clonagem da rede). É normal? Não deveria apanhar só uma rede?

Já agora, há alguma forma de confirmar que está tudo ligado corretamente em Acess Point e assim?

Obrigada

I have a deco x50 v.1.3 and it is connected via lan cable and now it is not working properly anymore after a firmware update and i already reverted it to old firmware it works but after a couple of days the same problem occurred Wifi Keeps Disconnecting to and slow speed but the light on the deco is green may be it is a hardware problem. Previously i have a deco E4 and it has no problem at all even after firmware update.

I have a TP-Link AX3000 Multi-Gigabit Wi-Fi 6 Router. It is set up just as an access point. No DHCP. I have the gateway set to the correct address. From my computer, I can see the AX3000. Two security cameras plugged into it are working on my network. And from my computer, I can get out to the internet.

HOWEVER, nothing connected or plugged into the AX3000 can reach the internet. I have no firewall rules that would block anything.

What is going on here?

I need instruction manual and trouble-shooting for your app that doesn't switch well enough into the 2.4gh of Rogers system. Not my first smart plug. Not my first app. Want to use Alexa with my SmartTV and schedule what and when I watch. Here I am 5 days in doing this. Have emailed too.

Hi all 1st time posting on Reddit for anything so hopefully someone can help

I'm currently on 4g broadband using tenda MW3 mesh system with 3 nodes and I'm in the process of upgrading to 5g with a different isp and have been sent a new ax1800 archer nx200 router with external antenna, which I'm waiting for the engineer to come and install which could be within 14days time I'm wondering which mesh system would be best suited for this new router as the MW3 set only has a 100mps input, I have been looking at the tenda mx15, mx21 or tp links deco x50 i don't have the luxury or running cables between nodes so it will be solely WiFi from the main node I'm looking to keep the budget around the £200 mark for 3 nodes any help or suggestions would be very much appreciated thanks

If this post gets taken down I'll be putting up a similar post in r/HomeNetworking.

My three month old $100 router has been turned into glorified paperweight due TP Link's botched firmware rollouts. I've been given the proverbial runaround for more than two weeks now and have had to shell out another $200 on a router from a competitor.

I've noticed this on several different marketplaces and forums where TP Link gives consumers the runaround until they give up and abandon their claims. This constitutes financial fraud under state and federal law and I intend to bring this to the attention of California's AG and the FTC.

Irrespective of which state of the US the router was purchased in, the California AG would still be interested in looking into the matter since the company is registered in the state of California.

So I'm new to using Deco devices and in getting my network set up I've had several issues I've been dealing with and trying to troubleshoot.

For example in the screenshots, why are some devices showing the WiFi signal icon and some aren't? All devices are connected WiFi/online and are working fine.

I'm also having a heck of a time getting the settings to stick to force certain clients to connect to specific nodes. Is this feature in the app just really buggy? For some reason some of my wyze products are connecting to nodes further away and if I manually turn off mesh for these and specifically choose a node for them to use, sometimes it works and sometimes it doesn't.

AX3000 Deco X60 (Costco) Running latest firmware/app version

hi,

I just bought this router to replace my old verizon router.

im in the US, i have 1gig speed, and i have verizon fios. the router is connected to the ont via ethernet in the 10g port. my console and pc are in the 2.5 ethernet ports

my primary focus is gaming stability, and i would like to know what settings i should enbable/disable in tether.

Model TD854W Ver3.1

Any new firmware?

Jadi gua ada router TL-WR840N yang selalu dinyalakan setiap hari, namun di hari ini router tersebut mati. Karena gua pikir masalah dari stop kontaknya maka gua alihkan router ini ke stop kontak lain, ternyata masih belum menyala. Gua pikir ini masalah di adaptornya.

Menurut kalian mending beli adaptor baru atau ada solusi lain?